RIDEIRON Winter Waterproof Goatskin Smart Heated Motorcycle Gloves with 4000mAh Battery | MG7506H

Upgraded Battery, Lasting Warmth
The upgraded 7.6V 4000mAh battery offers approximately 33% more capacity than the previous 3000mAh battery, providing around 4–7 hours of heating for cold-weather rides.

Supple Goatskin, Reinforced Protection
Extensive goatskin coverage adds a soft, premium feel while allowing comfortable hand movement. Thicker carbon fiber protective elements reinforce the glove without compromising its focus on comfort and control.

Waterproof Protection, Insulated Comfort
A HIPORA waterproof membrane helps keep rain and road spray out, while 3M Thinsulate insulation helps retain warmth. An upgraded plush lining adds a soft layer of comfort for cold-weather rides.

Fast Heat. Smart Control.
Carbon nanotube film heating delivers a rapid 3-second heat-up, with 360° heating coverage to surround your hands with warmth. Choose from three manual heat settings or use smart temperature control to suit your ride.

Fast Charging and Built-In Protection
Supports USB and Type-C charging, compatible with wall adapters, power banks, and motorcycle USB ports. A built-in protection circuit monitors power flow, triggering a purple indicator light and auto shut-off when short circuit or overload is detected.

Touchscreen Convenience
Touchscreen-compatible fingertips let you use your phone or compatible navigation device without removing your gloves, keeping your hands covered during quick stops.

Q1: Why does the controller Light Flashing Purple?
A:

1. Unplug the power from your device.

2. Wait 5 minutes.

3. Reconnect the battery.

4. Press and hold the switch for 2 seconds to restart the device

Solution: If the issue persists, the components or battery may be damaged.
Please contact customer support for assistance.

Q2: My glove does not heat up. What should I do?
A:
1. Check the Battery Connection: Ensure the battery is fully charged and securely connected to the glove.
2. Inspect the Battery Status: Verify the battery’s charge level. If it’s low, recharge it and test again.
3. Test the Power Button: Make sure the power button is functioning correctly. Press and hold it to activate the glove.
4. Swap the Battery: If possible, try a different battery to determine if the issue is with the current battery.

Solution: If these steps don’t resolve the issue, the glove or battery may be defective.
Please contact customer support.

Q3: Not Heating Enough / Temperature Difference Between Left and Right—What should I do?
A:
1. Check the Battery Connection: Ensure the battery is fully charged and securely connected to the glove.
2. Swap Batteries: Switch the batteries between the gloves to see if the issue moves with the battery.
3. Verify the Settings: Ensure both gloves are set to the same temperature level.
4. This product uses NTC temperature control to ensure a comfortable temperature, so it may not feel very hot (i.e., it will not burn your hands).
5. Variations in hand size and how the gloves are worn may cause differences in temperature. After prolonged use, the temperature sensation will converge.

Solution: If the problem persists, it could be a heating element issue. Please contact customer support.

Q4: My glove’s battery isn’t charging. How can I fix this?
A:
1. Check the Charger and Cable: Ensure the charging cable and adapter are functioning. Test them with another device if possible.
2. Inspect the Charging Port: Check for debris or damage in the battery’s charging port.
3. Try a Different Outlet: Use a different outlet to rule out issues with the current one.
4. Reset the Battery: Disconnect and reconnect the battery to see if that helps.

Solution: If the battery still won’t charge, it may be defective. Please contact customer support.

Q5: My glove shuts off unexpectedly. What should I do?
A:
1. Check the Battery Level: Ensure the battery is fully charged. A low battery may cause the glove to shut off.
2. Inspect for Overheating: The glove might automatically shut off to prevent overheating. Let it cool down before using it again.

Solution: If the glove continues to shut off unexpectedly, it may need inspection by the manufacturer.
Please contact customer support.